Dinnissen Innovations during Interpack in Düsseldorf, Solids in Dortmund and Victam in Cologne

Dinnissen is developing by a mix of innovations.
Dinnissen
has broadened the deployability of its mixers, thanks to a mix of innovations. The mixers have been further improved in several areas, and, moreover, they explicitly consider the role of the mixer in the overall operation. That is why the validation of mixing processes have now been added to their service.

Fig. 1: Lean gravity by Dinnissen: turnkey concept to completion


Dinnissen Process Technology
is actively engaged in the development and manufacture of process equipment such as grinding mills, mixers, bulk bag filling systems, turnkey projects for the food industry, animal feed industry, pharmaceuticals and chemicals. The company is a specialist in prudent, hygienic and rapid mixing of powders, pellets and granules. They never shirk challenges such as achieving higher capacities, improving homogeneous mixing of micro-components, mixing poor flowing materials or processing high percentages of liquid. On the contrary; Dinnissen is constantly looking for applications that are a trigger for the development of even better mixers.

Improved D-Topline
The desire for constant innovation has recently led to the introduction of the ‘Improved D-Topline’, a model based on the familiar Pegasus double-axle paddle mixer. The geometry of the installation is modified in such a way that the upper sides of the mixing chamber lean in towards each other, resulting in a drop shape. The negative angle of inclination in the upper side of the mixing chamber reduces the risk of product adhesion. In addition, the ‘Improved D-Topline “can be equipped with an additional hatch (‘front hedge’) on the front. This feature makes it much easier to inspect or clean the mixer. In some cases, thanks to this hatch, a version can be offered where the paddle axle assembly can be driven entirely from the mixing chamber.

Furthermore, the ‘Improved D-Topline’ is provided with a divisible shaft seal, allowing the installation to be CIP-cleanable.

Fig. 2: The improved D Topline mixer is easy to clean


High-shear mixer
Dinnissen
is at an advanced stage of optimising high-shear applications in the mixing process, which are also based on the Pegasus mixing principle. There are applications in which powders require a greater frictional force in order to obtain a homogeneous product.

A change in the paddle configuration ensures that the new high shear process applies the necessary energy to the product, but without sacrificing the typical advantages of the Pegasus mixer.

Explosion-proof mixer
Yet another development is the introduction of an explosion-proof mixer (Atex-zone 20 internal), suitable for processing materials in which the Kst- and LEL-values ​​are within a fixed range. This mixer was subject to a risk assessment and received a type approval for the entire Pegasus mixer range from an independent Notified Body.

‘All in one’ concept
The ‘All in one’ concept is Dinnissen’s response to the demand for fully integrated process lines. An example is the mixing line which has recently been shipped to a customer in the United States. This consists of a skid comprising a docking system for vessels which can be deposited into the mixer dust-free, which can then move the mixer up and down to mix and fill the same vessel again. The great advantage of the ‘All in one’ concept is that the various components are perfectly matched to each other. This means that a consistently high-quality product can be guaranteed. There is no segregation of the product, moreover the process is completely dust-free and explosion-proof.

Smart concept
Dinnissen is becoming increasingly involved in the concept stage with their customers. This lies in the fact that the company not only acts as a process specialist but also as a solution provider. Nowadays, processes are developed using 3D modelling, simulations and time analysis. Thanks to VR support (Virtual Reality), the customer can visualise the design of a process and have an idea of ​​the accessibility and possibilities of systems and components at a much earlier stage. One of the accomplishments of Pegasus mixers is that they are able to mix in concentrations as low as 0.1%. This offers the possibility of removing a premix-step, thereby simplifying the process and gaining the benefits of less handling and energy consumption.

Validation
The increasing interest in the role of the mixer in the overall production process translates into the need for Dinnissen’s customers to have the mixer validated. A validation makes it possible to determine which set of parameters will result in the raw materials being homogeneously mixed to produce an end product of the required quality. Thus, making it possible to reproduce the mixing processes. Dinnissen is also interested in this validation data, as it will allow them to further optimise their mixers. For that reason, Dinnissen has now added a validation of its mixing processes, which may, if required, be undertaken by an independent agency.

Multifunctional processing mixer
The Pegasus double-axle paddle mixer from Dinnissen Process Technology is ideally suited for the energy-efficient and product-friendly processing of a wide range of raw materials. The paddles create a fluid bed in the mixing chamber. The product particles can move freely in the fluidised zone, resulting in a quick and intensive mix. As a result, it is also possible to dry the particles with energy-efficient sucked or injected warm, dry air. The combination of various process steps (such as mixing and drying) in one system reduces the necessary floor space and saves on the purchase of process equipment. In addition, a combination of process steps minimises the effort required to clean a process line. The mixing and drying parameters of the mixer are easy to adjust, so that a variety of recipes can be easily produced from a single installation.

********************

Largest infant food plant in Europe works with Lean Gravity Mixing
The largest plant for infant food in Europe, was recently put into operation in central Brittany, France. The plant has a capacity of 100,000 tonnes/year. In addition to the drying towers, the heart of the process is based on an innovative dry mixing concept by the Dutch manufacturer, Dinnissen Process Technology, called Lean Gravity Mixing.

Adapted concept
The Chinese infant food manufacturer, Synutra (12,000 employees) has invested € 170 million in a new 38.000 m² greenfield mega-plant located in Carhaix-Plouguer, Brittany. This facility processes milk into dry baby food intended for export to China. The plant requires 288 million litres milk per year, which is provided by 800 farmers from the Sodiaal regional cooperative. The construction of this greenfield plant began in 2014 and the process involved a total of ten suppliers from ten different countries. Dinnissen Process Technology came into the picture at a relatively late stage with an unusual proposal for the dry mixing line. This turned out to have so many advantages that the concept of the plant and the design of the building were substantially adjusted to suit it.

No product conveyor lines
Synutra already operates four infant food plants in China and had their own tried and tested procedure with mixing line, silos storage for the finished product and pneumatic or screw conveyors to the packaging line. Dinnissen made a proposal for a lean gravity mixing line, which makes optimum use of gravity, so that product conveyor lines were no longer needed. This is beneficial because any mechanical transport, either pneumatically or by screws may cause damage to the product. In the gravity mixing line, all the raw material components are raised up and fully-automatically dosed into the mixer from above. The mixed product is discharged from the bottom of the mixer and goes through multiple process steps below by force of gravity. This does, however, require the necessary height to be available. Dinnissen has already built many lines according to this concept. Various sized mixers can be used with such mixing lines. In this case, Dinnissen has suggested a mixer with a capacity of 4 tonnes per batch, with a mixing time of approximately 1 to 1.5 minutes.

High care bulk bag handling
In the Carhaix plant, the milk powder resulting from the drying process and all other bulk ingredients are stored in bulk bags in a huge automated warehouse. This allows the difference between milk supply and the desired output of the plant to be gauged accurately. These bulk bags are the most important input for the mixing line. An AGV system carries the bulk bags to the beginning of the mixing line on level 1. They pass through a cleaning cabin, which disinfects the outside of the bulk bags with ionized air and UV, before entering the high-care area. A quick lift, with a capacity of 26 units per hour, brings these up to level 6, at a height of 24m. The bulk bags are then taken over by one of the four transport systems, which delivers them automatically to the correct unloading station (one of the six stations) via built-in floor guides. After a check scan by the operator and authorisation from the operating system, the bulk bag is hoisted and attached to the unloading station. This a high-care procedure due to the hygiene requirements. There are three different bulk ingredients with two bulk bag unloading stations for each ingredient; thus ensuring a constant supply of the three basic ingredients. Per batch, based on the desired formulation, the content of the correct bulk bag is added to the mixer situated directly below it. A “loss-in-weight” dosage is employed for accuracy.

Fig. 3: High care product intake


Minors
In addition to the contents of the bulk bags, there are also ‘minors’, which are ingredients in smaller volumes. There were 3 minors anticipated in the design phase, but in practice there are now around 30, which have been seamlessly integrated into the operation. The bags containing the ‘minors’ are cooled and transported to level 1. They enter the high-care area after passing through a UV tunnel to kill any bacteria. They are then collected in crates and moved to level 6 via the quick lift. The transport system then takes them to a set-down area, where the operator can store them temporarily. At a weighing station, the operator sets the required premixes together using a vacuum system, which once bagged, are moved to the dosing cabinet to be fed into the mixer. A number of scans are needed during the process to ensure that the operator formulates the correct mix and that it is added to the appropriate batch.

Pegasus mixer
The mixer, located at level 5, has a capacity of 6.5 m³, and can handle up to 4 tonnes which produces up to 14 tonnes of baby food per hour. The mixing time of a complete batch is only 1 to 1.5 minutes. The mixer is equipped with two large ‘wing doors’ on either side, in order to facilitate a periodic quick dry cleaning. This double-axle Pegasus paddle mixer, a tried and tested concept of Dinnissen, dissolves the batch at the bottom so that no residue remains. The mixed product then falls into a supply hopper on level 4 which has a sieve mounted below it. A metal detector and rotating magnet is used to remove any metal particles before the product flows further down to the packaging line. There is also the possibility to fill bulk bags during this process.

Fig. 4: The double-axle Pegasus paddle mixer

Security and hygiene
Synutra had initially based the design of the dry-mixing line on storage of the finished product in silos and pneumatic or screw conveyance to the mixers. The design was radically overhauled during the engineering phase because of the significant benefits of the Dinnissen Lean Gravity Mixing line. Firstly, there is no mechanical transport of the finished product; the product is moved by the natural force of gravity from the vertical mixing line to the packaging line. As a result, there is no risk of damage, segregation or product adhesion. It also means a lower consumption of energy.   The fact that Dinnissen has, in recent years, made many mixers for leading manufacturers of infant food, also played a role. The entire line is hygienically designed in such a way that it can be automated to be easily operated by 1 or 2 operators. Almost all the components were fabricated by Dinnissen in its own production plant in the Netherlands and this allows them to function as a turnkey supplier and systems integrator for the entire mixing line.

*****************

Modular mixer installation: security and time savings
Dinnissen has recently built a complete mixing plant for a German client, which includes six bulk bag unloading stations for the raw materials. The installation was intended for their new plant in Asia and the client wanted absolute assurance that the system worked smoothly with their somewhat sticky raw materials. It was also necessary to set up the facility in Asia in a very short period of time.

Fig. 5: Construction of 8 m high complete mixing plant in a separate hall at the factory of Dinnissen in Sevenum

The solution presented by Dinnissen consisted of a modular construction in a separate hall at their factory in Sevenum. The complete installation, 8 meters high, was assembled in a fully operational condition including wiring and controls. It consisted of a supply line with 6 bulk bag unloading stations, with the raw material dispensed through a Dinnissen Feeder Valve with ‘loss-in-weight’ dosing and transported to the Pegasus mixer by a bucket elevator. The final product was filled into bulk bags or containers.

All the process steps had already been tested in the tender phase by Dinnissen. This also included the FAT (Factory Acceptance Test) in the Netherlands, with four recipes and 20 runs. A genuine practical test. The entire installation, complete with platforms and stairs, was then disassembled and packed in seven 40ft containers and shipped. Upon arrival in Asia, the installation was assembled and commissioned by employees of Dinnissen’s Asian partner and a Dutch supervisor of Dinnissen. In this particular case, the employees had already been to the Netherlands to work on the original factory assembly and the FAT. This ensured good service and support and prevented any unforeseen surprises at the final site assembly. In terms of control, the operating software had already been integrated with the site software, so that the commissioning would be made even easier.

This modular concept and a FAT in the Netherlands means Dinnissen can offer producers not only 100% certainty about the operation of the installation, but also significant time savings during the assembly and commissioning on site.

 

More information on Dinnissen

Google Search – Web

Google Search – Images

Dinnissen on the Portal

Dinnissen Videos on bulk-online

Leave a Reply

Your email address will not be published. Required fields are marked *